Raymarine Home Security System E03016 User Guide

Installation  
Acute bends must be avoided.  
Introduction  
What’s in the box?  
Where a cable passes through an exposed  
bulkhead or deckhead, a watertight gland  
or swan neck tube should be used.  
CCTV camera cables cannot be cut and  
rejoined.  
A
Your Raymarine CAM  
50 CCTV camera is a  
good quality color  
camera available in two  
models:  
Installation  
Having selected a suitable installation site:  
B
•E03016 - NTSC  
format.  
•E03017 - PAL format.  
You cabn adjust both the pan and the tilt of the  
camera.  
1.Remove the  
camera dome by  
gently turning it  
counter-clockwise  
to release the  
bayonet fixing.  
2.Remove the  
camera cover by  
gently pulling it  
away from the  
dome baseplate.  
3.Hold the base-  
plate in the  
required position  
and using a  
pencil mark the  
fixing holes.  
It is waterproof to IP63 standard and suitable  
for use in indoor locations such as the wheel  
house, salon or engine room.  
To adjust the pan of the camera:  
1. Loosen screw A.  
2. Gently turn the camera assembly until the  
lens is pointing in the required direction.  
3. Gently pinch screw A to secure the camera  
in position.  
Safety notices  
What tools are required?  
To adjust the tilt of the camera:  
1. Loosen screw B.  
2. Holding the edges of the camera plate  
gently tilt the camera up or down into the  
required position.  
CAUTION: Power supply  
The CAM 50 CCTV camera is suit-  
able for use on a 12 V DC power  
supply only.  
Camera  
Phillips  
screwdriver  
Drill bit  
3. Gently pinch screw B to secure the camera  
in position.  
Drill  
CAUTION: Power supply  
A 0.5 A quick-blow fuse should be  
fitted to the positive (red) lead of the  
camera.  
What accessories are  
available?  
To enable you to complete the cabling to instal  
your camera the following are available:  
You should now connect the camera to your  
display and check that the required image is  
being shown.  
4. Using a suitable  
drill bit make pilot  
Either adjust the image by changing the pan  
and tilt as detailed above, or, replace the  
camera dome and cover to complete the  
installation.  
Dome  
CAUTION: Installation  
This product IS NOT suitable for  
installation underwater.  
E06017 - 5 m extension cable.  
E06018 - 15 m extension cable  
holes for the fixing  
screws.  
5.Fix the camera  
and baseplate into  
position using the  
two screws  
provided.  
6.Make sure that  
the cable is  
placed in the  
The cables can be joined in any combination to  
achieve the required cable length.  
This product contains no user  
serviceable parts.  
Cable connections  
Cable runs  
You need to consider the following points  
before installing your camera cables:  
Cover  
The extension cables from  
the camera to the display  
Female  
Male  
You need to connect the camera to a  
display unit and power supply.  
unit are joined using the  
male/female twist  
connectors.  
cable slot of the camera baseplate to  
ensure that it is not pinched when the  
baseplate is secured in position.  
With the camera installed you can now adjust  
the field of vision .  
All cables should be adequately clamped  
and protected from physical damage and  
exposure to heat - avoid running cables  
through bilges or doorways, or close to  
moving or hot objects.  
The adapter cable should  
be used to connect the display and the power  
supply to the camera. The adapter cable  
connections are shown below.  
 

RayTek Thermometer MX Series User Guide
RCA Camcorder CC634 User Guide
Reliable Sewing Machine MSK 8210M User Guide
Renesas Network Card R0E330850MSRC0 User Guide
Roland Electronic Keyboard MP 500 User Guide
Samsung Camcorder D102Di User Guide
Samsung Cordless Telephone SH u740 User Guide
Sanyo Air Conditioner WCHDZ20053 User Guide
Sanyo Projector PLC XD2600 User Guide
Scag Power Equipment Lawn Mower SVR36A 20FX User Guide