DAB / FM RDS digital clock radio with dual mode dimmer
Please read this manual before use
Controls (front view)
5
9 10 11
12
6 7
8
4
3
2
1
13
14
1. Dimmer button
6. Alarm button
7. Sleep button
8. Snooze button
9. Menu / Info button
10. Band button
11. Tuning Down button
12. Tuning Up button
13. Select button
2. On / Off button
3. Volume Down button
4. LCD display
14. Preset button
5. Volume Up button
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
2
Controls (rear)
15
16
17
18
15. FM / DAB wire aerial
16. DC input socket
17. Auxiliary input socket
18. Headphone socket
3
Using the clock radio for the first time
1. Place your clock radio on a flat surface.
2. Fully extend the wire aerial located on the rear of your clock radio.
Place the wire antenna so that it is straight as possible extending
either above or below the radio.
3. Insert the adaptor plug into the DC socket located on the rear of your
clock radio. Plug the adaptor into a standard 13 amp mains socket
outlet. The display will show "Roberts" for a few seconds and then
the display will show "Setting clock". The clock hands will then move
to 12:00. The radio will scan for DAB signals and if a DAB signal is
found it will then show the current time and date in the display. The
clock hands will then move to show the correct time.
4. If no stations are found, "Clock not set" will be displayed. It may be
necessarytorelocateyourclockradiotoapositiongivingbetterrecep-
tion. You should then carry out a scan to find stations as described on
page 8.
•
IMPORTANT: The mains adaptor is used as the means of connecting
the clock radio to the mains supply. The mains socket used
for the clock radio must remain accessible during normal use. In order
to disconnect the radio from the mains completely, the mains
adaptor should be removed from the mains socket outlet
completely.
Characters appearing on the LCD display indicate that the clock radio is
connected to and powered from the mains supply.
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
4
Selecting a station - DAB
1. Place the wire antenna so that it is as straight as possible extending
either above or below the radio.
2. Press the On/Off button to switch on your clock radio.
2
3. During the clock setting the radio carried out a quick scan of the UK
DAB channels. If this was not successful or if you have moved the
radio to a different part of the country follow the Auto tune procedure
page 8. During Autotune, the display will show "Scanning" and as
each group of stations is detected the station count will be updated.
The bottom line of the display shows a bargraph indicating progress
of the Autotune. When the Autotune is completed the first station (in
numeric-alpha order 0...9...A....Z) will be selected.
4
4
4. Thetoplineofthedisplayshowsthenameofthestationcurrentlyselected.
PresstheTuningUp/Downbuttons toscrollthroughthelistofavailable
stations. Stop pressing the Tuning up or down buttons when you find
the station that you wish to hear.
5
5. Press and release the Select button to select the station. The display
may show "Now tuning" while your radio finds the new station.
6. Adjust the Volume buttons to the required setting.
6
6
Note: If after selecting a station the display shows "Not Available" it
may be necessary to relocate your radio to a position giving better
reception.
5
Presetting stations - DAB and FM
You may store your preferred DAB and FM radio stations to the preset
station memories. There are 20 memory presets in your clock radio, 10
for DAB and 10 for FM. Presets are remembered by your clock radio in
the event of a power failure.
1
The procedure for setting presets and using them to tune to stations is the
same for FM and DAB modes and is described below.
1. Press the On/Off button to switch on the clock radio.
2. Tune to the required station as previously described.
3. Press and release the Preset button.
3
4. Press the Tuning Up/Down button until you find the required preset
4
number in which you wish to store the chosen station.
4
5. Press and hold the Preset button until the display shows e.g. "Preset
1 saved". The station will be saved under the chosen preset memory.
Repeat this procedure for the remaining presets.
5
6. Stations stored in preset memories may be overwritten by following
the above procedure.
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
6
Recalling a preset
1. Press the On/Off button to switch on your radio.
2. Press and release the Preset button.
1
3. Press the Tuning Up/Down button until you find the required preset
number.
2
4. Press and release the Select button. Your radio will tune to the station
stored in preset memory.
Note: If you have not previously stored a preset station and the preset
buttons are pressed "Empty preset" will be displayed.
3
3
4
7
Finding new stations - DAB
As time passes new stations may become available. To find new stations
proceed as follows:-
1
1. Press and hold the Menu/info button until "Station order" appears
on the display.
2
2. PresstheTuningUp/Downbuttonsuntilthedisplayshows"Autoscan
2
local".
3. Press and release the Select button, the display will show
"Fast scanning". Your radio will perform a scan of the UK DAB
frequencies. As new stations are found the station counter on the
right-hand side of the display will increase and stations will be added
to the list.
3
4
4. If you are not living in the UK, you may need to scan a wider range
of frequencies. To carry out a full scan of the entire DAB Band III
frequencies press and hold the Menu/info button until "Station order"
appears on the display.
5. PresstheTuningUp/Downbuttonsuntilthedisplayshows"Autoscan
full".
5
5
6. Press and release the Select button, the display will show
"Full scanning". As new stations are found the station counter on
the right-hand side of the display will increase and stations will be
added to the list.
6
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
8
Manual tuning - DAB
Manual tuning allows you to tune directly to the various Band III DAB
channels. UK DAB stations are currently located in the range 11B to
12D.
1
1. Press and hold down the Menu/Info button, "Station order"
appears on the display. Then press the Tuning Up/Down button until the
display shows "Manual tune". Press and release the Select button.
1,2
1,2
2. Press the Tuning Up/Down button to select the required DAB channel.
3. PressandreleasetheSelectbuttontoselectthechannel.Anynewstations
that are found are automatically added to the stored list of stations.
1,3,4
4. Press and release the Select button to return to normal tuning mode.
Secondary services - DAB
1. Certainradiostationshaveoneormoresecondaryservicesassociated
with them. If a station has a secondary service associated with it the
display will show ">>" next to the station name on the station list. The
secondary service will then appear immediately after the primary
service when you press the Tuning Up/Down button.
1
1
2. Press and release the Select button to select the station.
•
When the secondary service shuts down, your radio will automatically
switch back to the main radio station (or primary service) if it is
available.
2
9
Display modes - DAB
Your radio has seven display modes for DAB radio:-
1. Press the Info button to cycle through the various modes.
a
b
c
a. Scrolling text
Displays scrolling text messages such
as artist/track name, phone in number,
etc.
1
b. Programme type
c. Multiplex name
Displays type of station being listened to
e.g. Pop, Classic, News, etc.
Displays name of DAB multiplex to which
the current station belongs.
d
e
d. Time and date
Displays current time and date.
e. Channel and frequency
f. Audio type and bit rate
g. Signal strength
Displays current channel and frequency.
Displays audio type and bit rate.
f
g
Displays a signal error value for station
being listened to (lower is better)
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
10
Dynamic Range Control (DRC) settings - DAB
The DRC facility can make quieter sounds easier to hear when your radio
is used in a noisy environment.
1
1. Press the On/Off button to switch on your clock radio.
2. Press and hold in the Menu/Info button until display shows “Station
order.”
2
3. Press the Tuning Up/Down button until the display shows "DRC
value".
4. Press and release the Select button to enter adjustment mode.
3,5
3,5
5. Press the Tuning Up/Down button to select required DRC setting
(default is 0).
DRC 0 DRC is switched off, Broadcast DRC will be ignored.
DRC 1/2 DRC level is set to 1/2 that sent by broadcaster.
DRC 1 DRC is set as sent by broadcaster.
4,6
6. PressandreleasetheSelectbuttontoconfirmthesetting.Thedisplay
will return to radio mode.
Note: Not all DAB broadcasts are able to use the DRC function. If the
broadcast does not support DRC, then the DRC setting in the radio will
have no effect.
11
Station order setup - DAB
Your radio has 3 station order settings from which you can choose. The
station order settings are, favourite station, alphanumeric and active
station.
1
Note: Your radio default station order is alphanumeric.
1. Press and hold in the Menu/Info button until "Station order" appears
on the display. Press and release the Select button.
1
2. Press the Tuning Up/Down button to choose between favourite
station, alphanumeric and active station.
Favourite stations
2
2
When this setting is switched on, after a period of time the most listened
to stations will move to the top of the station list and will be marked with
the heart symbol
.
Alphanumeric
Press the Tuning Up/Down button until "Alphanumeric" appears on the
display. Your radio will now select stations in alphanumeric order A....Z
0....9.
Active station
Press the Tuning Up/Down button until "Active station" appears on the
display. The display will show only those that a signal can be found.
3
3. Press and release the Select button to select the station order
setting required.
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
12
Prune stations - DAB
Some DAB services may stop broadcasting or you may not be able to
receive a station. Prune stations will delete the DAB stations from your
station list that can no longer be received.
1
1. Press and hold in the Menu/Info button until "Station order" appears
on the display. Press and release the Select button.
1,2
2. Press the Tuning Up/Down button until "Prune stations" appears
on the display. Press and release the Select button to select.
2
2
Signal strength display - DAB
1. Press and release the Select button to show signal strength on the
lower line of the display.
1,3
2. Positionyourradioandcarefullyanglethewireaerialforbestreception
using the signal strength display as a guide. Move your radio around
andpositiontogivemaximumnumberofblackrectanglesonthesignal
strength display.The clear unfilled rectangle indicates minimum signal
level required for satisfactory reception.
3. Press and release the Select button to return to the previous display
mode.
13
Operating your radio - Search tuning FM
1. Place the wire antenna so that it is as straight as possible extending
either above or below the radio.
2
2. Press the On/Off button to switch on your clock radio.
3. Press the Band button to select the FM band, then repeatedly press
3
the Select button until "Auto tune" shows on the display.
4. Press and release the Tuning Up button. Your radio will scan in
an upwards direction (low frequency to high frequency) and stop
automatically when it finds a station of sufficient strength.
3
5. After a few seconds the display will update. The display will show the
frequency of the signal found. If the signal is strong enough and there
is RDS data present then the radio will display the station name.
4,6
7
6. To find other stations, press and release the Tuning Up button as
before.
7. To scan the FM band in a downwards direction (high frequency to low
frequency) press and release the Tuning Down button.
9
9
8. Whenthewavebandendisreachedyourradiowillrecommencetuning
from the opposite waveband end.
9. Adjust the Volume buttons to the required setting.
10. To switch off your radio press the On/Off button.
10
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
14
Manual tuning - FM
1. Press the On/Off button to switch on your clock radio.
1
2. Press the Band button to select the FM band. Fully extend the
wire antenna for FM reception.
3. Repeatedly press the Select button until "Manual tune" shows on the
2
display.
4. Press the Tuning Up/Down button to tune to a station.The frequency
will change in steps of 50 kHz on FM.
3
5. When the waveband end is reached the radio will recommence tuning
from the opposite waveband end.
6. Set the Volume buttons to the desired settings.
4
4
7. To switch off your clock radio press the On/Off button.
6
6
7
15
Display modes - FM
Your radio has four display modes for FM radio. These use data provided
by broadcasters which is commonly known as RDS.
The Radio Data System (RDS) is a system in which inaudible digital
information is transmitted in addition to the normal FM radio programme.
RDS offers several useful features. The following are available on your
radio:-
a
1. Press the Info button to cycle through the various modes.
1
a. Scrolling text
Displays scrolling text messages such
as artist/track name, phone in number,
etc.
b
c
d
b. Programme Type
Displays type of station being listened to
e.g. Pop, Classic, News, etc.
c. Time and date
d. Frequency
Displays the current time and date.
Displays the frequency of the station
being listened to.
If there is no RDS data available (or if the signal is too weak) then the radio
will display only the FM frequency and the optional Stereo indicator.
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
16
Stereo / Mono setting - FM
Your clock radio will play stereo broadcasts in stereo (via headphones) so
long as the received signal is of adequate strength. However, as a stereo
signal becomes weaker the audio signal will become poorer. It may be
preferable to force the radio to play the station in mono in order to reduce
the level of audio noise.
1
1. Press the On/Off button to switch on your radio.
2. Tune to the required FM radio station as previously described.
3. Press and hold the Menu/Info button until the display shows "Mono
override" on the lower line. The upper line will show "Override Off" if
the radio is in the Auto-Stereo mode.
3,5
4,6
4. Press the Select button to switch on the Mono-Override. While this
setting is engaged, the radio will play the current station in mono
whether listening via headphones or the loudspeaker.
Mono Overide is a temporary setting and is applied to the currently
tuned station only. It is cancelled automatically by tuning to another
radio station.
5. If you wish to cancel Mono-Overide while listening to the currently
tuned radio station, press and hold the Menu/Info button until the
display shows "Mono override" on the lower line. The upper line will
show "Override On" if the radio is in the Mono-Overide mode.
6. Press the Select button to switch off the Mono-Override. The radio
will play then play the current station in stereo through headphones
if the signal is sufficiently strong.
17
Auto preset stations - FM
Your clock radio will scan the entire FM band searching for stations. As
stations are found, they are stored in your clock radio preset memory
locations.
1
1. Press the On/Off button to switch on your radio.
2. If needed, press the Band button to select the FM band.
2
3. Press and hold the Menu/Info button until the display shows "Mono
override" on the lower line.
4. Press and release the Tuning Up/Down buttons until the display
shows "FM Scan".
3
5. Press the Select button to confirm the scan.
Note: Some of the FM stations stored may be quite weak as the scan
stores stations regardless of their signal strength. Up to ten stations
will be stored. Presets can be modified as needed using the procedure
described on page 6.
4
4
5
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
18
Alarms
Your clock radio has four separate alarms which can be set to wake you to
radio (DAB, FM) or buzzer alarm. Each alarm can be set to sound once,
daily, on weekdays or at weekends. The alarms can be set whether the
clock radio is on or in standby mode. In the event of a power interruption
your clock radio has a built in memory chip that will maintain all your alarm
settings for when the power is restored.
Note: If no buttons are pressed for 5 seconds, the radio will exit the alarm
setup.
Note: Alarm times are set using the 24Hr format e.g. 2:30PM is entered
as 14:30.
1
Setting an alarm
1. Press and release the Alarm button. "Set alarm" will show on the
display. Press the Select button the alarm status will show on the
display.
2-4
2-4
2. RepeatedlypressandreleasetheTuningUp/Downbuttonstochoose
the desired alarm 1-4 and then press the Select button. The alarm
hour will be highlighted.
2-4
3. RepeatedlypressandreleasetheTuningUp/Downbuttonstochoose
the desired hour for the alarm and then press the Select button. The
alarm minute will be highlighted.
4. RepeatedlypressandreleasetheTuningUp/Downbuttonstochoose
the desired minute for the alarm and then press the Select button.
The alarm source will be highlighted.
19
5. RepeatedlypressandreleasetheTuningUp/Downbuttonstochoose
the desired source for the alarm (DAB, FM or Buzzer) and then press
the Select button to confirm the audio setting.
5,7
5,7
6. Your alarm can be set to sound once, daily, weekdays and week-
ends.
Once
Daily
- Will sound at one time only.
- Will sound every day.
Weekdays
Weekends
- Will sound only on weekdays.
- Will sound only on weekends.
5,7
7. RepeatedlypressandreleasetheTuningUp/Downbuttonstochoose
thedayoptionandthenpressandreleasetheSelectbuttontoconfirm
the setting.
•
If setting alarms to daily, weekdays or weekends proceed to point
12.
8. If selecting the alarm to once you will need to set the year, month and
day options as described below.
9,10
9,10
9. Press the Tuning Up/Down button to select the correct year and
then press the Select button to confirm the setting.
9,10
10. Press the Tuning Up/Down button to select the correct month and
then press the Select button to confirm the setting.
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
20
11. Press the Tuning Up/Down button to select the correct day and then
press the Select button to confirm the setting.
12. Thealarmhasnowbeensetandtheradiowillreverttothepreviousradio
display mode. The alarm symbol (bell) will appear on the display.
11
When the alarm is set to wake by radio, the last used station will be
switched on at the alarm time.
11
While the alarm is sounding, normal radio controls are not available. The
alarm indicator (bell) will flash.
11
If the buzzer alarm is used, the volume will start from minimum and
increase in level every few seconds. The alarm will sound for 60 minutes
unless cancelled.
To cancel the alarm
1. While an alarm is sounding it can be cancelled by pressing the On/Off
button. The alarm will then be rescheduled as needed according to
its settings.
Note: Pressing the On/Off button once during a radio alarm cancels the
alarm but allows the radio to continue playing. Pressing the On/Off button
a second time will put the radio back into standby mode.
1
21
To switch the alarm on or off
1. Press and release the Alarm button, "Set alarm" will show on the
1
display.
2. Repeatedly press and release the Tuning Up/Down button until
"Alarm On/Off" shows on the display.
2,4
2,4
3. Press the Select button to enter alarm status setup.
4. Repeatedly press and release the Tuning Up/Down button until the
desired alarm 1-4 is displayed.
3,5,6
5. To disable a set alarm press the Select button and the alarm symbol
(bell) will be removed from the display. The alarm will be cancelled.
6. ToenablethesetalarmpresstheSelectbuttonuntilthealarmsymbol
(bell) shows on the display. The alarm will now activate at the set
time.
1
1
To view set alarm times
1. Press the Alarm button, then press the Select button to enter alarm
setup.
2. Repeatedly press and release the Tuning Up/Down button to view
the current alarm settings.
2
2
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
22
Snooze
1. When the radio or buzzer alarm sounds, pressing the Snooze button
will silence the alarm for the selected number of minutes. The Snooze
can be adjusted between 5 and 60 minutes in 5 minute increments.
The display willl show the Snooze symbol. This sequence can be
repeated during the 60 minute buzzer alarm period.
1
To set the snooze time
1. Press the On/Off button to switch on the clock radio.
1
2. To set the Snooze time, press the Alarm button "Set alarm" will
appear on the display.
3. Press the Tuning Up/Down buttons until "Snooze" appears on the
display. Press and release the Select button. The set snooze time
will show on the display.
2
4. Press the Tuning Up/Down buttons to choose the desired snooze
setting from between 5 - 60 minutes or Off. Selecting Off will disable
the snooze function.
3,4
3,4
5. PresstheSelectbuttontoconfirmthedesiredsnoozesetting.Theradio
will exit the menu options and return to the normal radio display.
3,5
23
Sleep function
Your clock radio can be set to turn off after a preset time has elapsed. The
sleep setting can be adjusted between 5 and 60 minutes.
1. To set the desired sleep time, press the Sleep button to enter the
1,2,3
sleep setup.
2. Repeatedly press the Sleep button to select the desired sleep time.
The sleep setting will increase in 5 minute increments from 5 minutes
to 60 minutes. A further press will cause the sleep timer to be set to
OFF which will cancel the sleep function. Alternatively the Tuning Up
or Down buttons may be used. The press the Select button to confirm
the setting.
3. Duringcountdownperiod, pressSleepbuttontoviewcountdowntime
left.
1
4. Your radio will switch off after the preset sleep time has elapsed.
5. To cancel the sleep function before the preset time has elapsed, either
press the On/Off button to turn the radio off or use the Sleep button
to show the "Off" option then press Select button to confirm.
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
24
Setting the clock manually
If you are unable to receive DAB broadcasts, the clock may be set
manually using the following procedure. Note that the radio may be on
or in standby mode when setting the time manually.
1
1. Press and release the Alarm button and repeatedly press the
Tuning Up/Down buttons until "Set clock" appears on the display.
1,3
1,3
2. Press the Select button to enter clock time setup. The hour digits
will be selected.
3. Repeatedly press the Tuning Up/Down buttons to choose the
desired hour and then press the Select button to confirm the hour
setting.
2-7
4. Repeatedly press the Tuning Up/Down buttons to choose the
desired minute and then press the Select button to confirm the
minute setting.
5. Repeatedly press the Tuning Up/Down buttons to choose the
desired year and then press the Select button to confirm the year
setting.
4-7
4-7
6. Repeatedly press the Tuning Up/Down buttons to choose the
desired month and then press the Select button to confirm the
month setting.
7. Repeatedly press the Tuning Up/Down buttons to choose the
desired day and then press the Select button to confirm the day
setting.
8. The clock should then set to the selected time, and the display will
show the correct time and date whenever the radio is in standby
mode.
25
To return to auto clock set mode
1. Press and release the On/Off button to switch on the clock radio.
2
2. Press and release the Alarm button and repeatedly press the
Tuning Up/Down buttons until "Auto-set clock" appears on the
display.
3. Press the Select button to confirm and your radio will return to
normal radio mode.
2
2
Note: If you select "Auto-set clock" the current time received will be
displayed. If no DAB signal is found you should either position the radio
or its aerial so that a signal can be received, or revert to manual clock
mode (see page 25).
3
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
26
Software version
The software display cannot be altered and is just for your reference.
1
1. To view which software version your radio has press and hold in the
Menu/Info button.
2. Press the Tuning Up/Down button until the software version shows
on the display.
2
2
Dual mode dimmer backlight
Your clock radio has two separate dimmer settings so that you can adapt
the intensity of the display to suit the ambient room lighting when the clock
radio is in standby mode and when it is switched on.
1. Whether your clock radio is on or in standby, repeatedly press the
Dimmerbuttononthetopofyourradiotoselectthedimmerbrightness
level you require. The dimmer button will cycle through the different
intensity settings.
1
2. There are four dimmer brightness levels available as well as an off
setting, should you wish to turn off the dimmer backlight.
27
System reset
If your radio fails to operate correctly, or some digits on the display are
missing or incomplete carry out the following procedure.
2
1. Switch on your radio.
2. Press and hold in the Menu/Info button.
3
3
3. Press the Tuning Up/Down button until the display shows "Factory
reset".
4. Press in and release the Select button, the display will show "Press
SELECT to confirm reset . . .".
4,5
5. Press the Select button to confirm. A full reset will be performed and
all presets and station lists will be erased. A quick scan of UK DAB
band III frequencies will be carried out. The clock will be set when the
radio recieves time information from the DAB radio station.
In case of malfunction due to electrostatic discharge, reset the product
(reconnection of power source may be required) to resume normal
operation.
If a problem persists our technical staff would be pleased to offer any
assistance on operating the radio. Our technical helpline number is
020 8758 0338.
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
28
Auxiliary input socket
1. Connect a stereo or mono audio source (ie CD player, MP3 player)
2
to the Auxiliary input socket.
2. Press the On/Off button to switch on your clock radio and the display
will show "AUX IN".
3. Adjust the Volume control on your player for comfortable listening.
When using the AUX IN mode, the volume control on the radio has
no effect.
4. Remove the cable from the Auxiliary input socket to cancel auxiliary
input mode.
Note: The volume control on your clock radio is bypassed when using
the Auxiliary Input. Therefore you must use the volume control on the
connected player to set the listening level as needed.
29
Headphone socket
A3.5mm Headphone socket located on the rear of your radio is provided
for use with either headphones or an earpiece. Inserting a plug automati-
cally mutes the internal loudspeaker.
IMPORTANT:Excessivesoundpressurefromearphonesandheadphones
can cause hearing loss.
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
30
•
•
•
Your clock radio should not be exposed to dripping or splashing and
no objects filled with liquids, such as vases, shall be placed on the
clock radio.
It is recommended to operate the product such that there is a minimum
distance (10cm recommended) to adjacent objects in order to ensure
good ventilation.
The ventilation of the product should not be restricted by covering it or
its ventilation openings with items such as newspapers, tablecloths,
curtains etc.
General
Do not allow this radio to be exposed to water, steam or sand. Do not
leave your radio where excessive heat could cause damage such as in
a parked car where the heat from the sun can build up even though the
outside temperature may not seem too high.
•
•
No naked flame sources such as lighted candles should be placed on
the product.
It is recommended to avoid using or storing the product at extremes
of temperature.Avoid leaving the unit in cars, on window sills, in direct
sunlight etc.
The name plate is located underneath your clock radio.
31
Specifications
Circuit features
Loudspeaker
63mm
Power Requirements
AC adaptor
AC 230 volts, 50Hz
only
Output Power
600mW
Frequency Coverage
Headphone socket
Aux in socket
3.5mm dia
3.5mm dia
DAB
FM
174.928 - 239.200MHz
87.50 - 108 MHz
Aerial System
DAB and FM
Wire antenna
The Company reserves the right to amend the specification without notice
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
32
Notes
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
......................................................................................................................................................................................................
33
Guarantee
This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component
breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free
of charge.
The guarantee does not cover:
1. Damage resulting from incorrect use.
2. Consequential damage.
3. Receivers with removed or defaced serial numbers.
Procedure:
Any claim under this guarantee should be made through the dealer from whom the instrument was purchased. It is likely that your Roberts' dealer
will be able to attend to any defect quickly and efficiently but should it be necessary the dealer will return the instrument to the Company’s service
department for attention. In the event that it is not possible to return the instrument to the Roberts' dealer from whom it was purchased, please contact
Roberts Radio Technical Services at the address shown below.
These statements do not affect the statutory rights of a consumer.
If you need any further advice, please call our Technical Helpline on :-
34
020 8758 0338 (Mon-Fri)
ROBERTS RADIO TECHNICAL SERVICES
97-99 Worton Road
Isleworth Middlesex
TW7 6EG
Technical Helpline :- 020 8758 0338 (Mon-Fri during office hours)
© 2008 Roberts Radio Limited
Issue 1
|