COFFEE MACHINE
ZCOF636X
UK
INSTRUCTION BOOK
ENGLISH
INSTALLATION AND
MAINTENANCE
FOR YOUR PERSONAL
SAFETY
•
•
•
The appliance should be installed and
connected to mains by QUALIFIED
PERSONNEL only. Before carrying out any
work on the appliance always make sure that it
has been DISCONNECTED from the mains.
Remove the appliance from the packaging,
check it for damage and make sure that the
power supply cable is in perfect condition. If
any damage is apparent contact your retailer
before using the appliance.
This new appliance is easy to use.
However, it is important to read the
whole of this booklet before installing
or using the appliance for the first
time. This will enable you to obtain
the best results from the appliance, to
avoid incorrect use and to use the
appliance safety and with respect for
the environment.
The Manufacturer declines all responsibility
if the instructions in this book are not
adhered to.
DURING USE
RECOMMENDATIONS FOR
SAFEGUARDING THE
ENVIRONMENT
•
•
The appliance should be used by adults only.
Make sure that children do not touch the
controls or play with the appliance.
It is dangerous to modify or to attempt to modify
the characteristics of this product.
PACKAGING
•
•
Keep the appliance clean at all times.
•
All packaging material is environmentally
friendly and can be recycled. Please help
safeguard the environment by disposing of
packaging correctly using the waste disposal
sites in your area.
The external parts of the appliance heat up when
the appliance is in use and remain hot for a
certain length of time after it has been turned off.
Keep children away from the appliance until
it has cooled down.
AT THE END OF THE APPLIANCE’S LIFE
•
•
Always make sure that the appliance is
disconnected from mains before carrying out
maintenance work and before cleaning the
appliance.
Never attempt to repair faults yourself.
Repairs carried out by unqualified persons may
result in damage to the equipment or personal
injury. Consult this booklet and if you do not
find the information you are looking for contact
your nearest Service Centre. This appliance
should be serviced by authorised Technical
Service Centres only. Always ask for original
spare parts to be used.
•
When the appliance is to be scrapped, cut off
the power supply cable.
•
Check with your local Council or
Environmental Health Office to see if there are
facilities in your area for re-cycling the
appliance.
This instruction booklet should be kept with the
appliance for future reference. If the appliance
is sold or transferred, make sure that the
booklet is handed over to the new owners so
that they are aware of the operating instructions
and relative warnings.
1
INDEX
INFORMATION FOR THE USER
INFORMATION
INSTALLER
FOR
THE
DESCRIPTION OF THE
COFFEE MACHINE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
PAGE
3
4
5
6
6
6
7
TECHNICAL SPECIFICATIONS
INSTALLATION
PAGE 12
PAGE 12
FIRST USE
MAKING COFFEE
HOT WATER
WATER SUPPLY
PAGE 15
PAGE 16
ELECTRICAL CONNECTION
STEAM
DRAWER
PAGE 17
RECIPES
CLEANING & MAINTENANCE
FAULTS
PAGE 10
TECHNICAL ASSISTANCE
AND SPARE PARTS
PAGE 10
PAGE 11
GUARANTEE CONDITIONS (UK)
GUARANTEE AND SPARE PARTS
(ONLY FOR BENELUX)
PAGE 12
EC
This appliance conforms to directive BT
73/26
ꢀ
concerning electrical safety standard EN
60335-1 (August 1995 – Safety of electrical
appliances for domestic use and similar –
General Standards) and EN 60335-2-15 (April
1996 – Special standards for liquid heating
appliances).
ꢀ
Directive EMC 89/336 concerning the
following standards:
− 55014-1
− 55014-2
− 61000-3-2
− 61000-3-3
2
DESCRIPTION OF THE
COFFEE MACHINE
1. Steam knob
2. Grinding texture knob
3. On button
4. Coffee button
5. Hot water button
6. Steam button
7. Light button
8. Orange 'ON' indicator light
9. Red 'water temperature' indicator light
10. Green 'coffee' indicator light
11. Green 'water' indicator light
12. Green 'steam' indicator light
13. Green 'light on' indicator light
14. Green 'dispenser' indicator light
15. Filter holder ring nut
16. Steam spout
17. Coffee press
18. Grinder button
19. Coffee dispenser
20. Filter-holder
21. One-cup filter
22. Two-cup filter
23. Coffee scoop
24. Unit clamping lock
25. Drip tray
26. Coffee bean holder
27. Water tank
28. Drawer (optional)
29. Fixing bracket
3
• The texture of ground coffee can however be
adjusted using the grinding texture knob (ref.2).
Turn the knob clockwise for a finer texture and
stronger coffee. Turn anticlockwise for a coarser
grind and weaker coffee.
FIRST USE
FILL THE WATER TANK
• Water hardness:
-
before filling the water tank make sure that the
Brita filter is in place (see paragraph "Water
supply").
PROGRAMMING THE QUANTITY
OF GROUND COFFEE
-
if the appliance has not been used for a long time
it is advisable to replace the water in the tank
with fresh water and to empty the boiler by
pressing the coffee button (ref.4) repeatedly.
• The machine is supplied already calibrated
to supply the ideal measure of ground coffee
for a cup of espresso.
• Open the unit clamping lock (ref.24) using the
• However, the quantity of ground coffee
supplied can be increased or decreased as
follows:
key supplied.
• Pull the coffee machine out of the unit on the
telescopic runners.
place the filter holder (ref.20) with a one-cup
filter (ref.21) below the coffee dispenser outlet
(ref.19) and press the grinder button (ref.18)
gently, do not release the button immediately.
After approx. 10 seconds the grinder will start,
when the quantity required is reached
(recommended measure 7g corresponding to 6
seconds of grinding) simply release the button
(ref.18) and the amount is automatically
programmed.
• Fill the water tank (ref.27) located on the left-
hand side of the appliance with approx. 2,5 litres
of water.
• Push the machine back into the unit and fasten
the unit clamping lock.
FILL THE COFFEE BEAN HOLDER
• Open the unit clamping lock (ref.24) using the
key supplied.
PRELIMINARY START-UP
• Pull the coffee machine out of the unit on the
telescopic runners.
•
Only move the steam spout using the rubber
handle.
Turn the coffee machine on by pressing the ON
button (ref.3). The orange indicator light (ref.8)
lights up to indicate that the machine is
connected to the power supply.
• Pour approx. 200g of coffee beans into the
coffee bean holder (ref.26) on the right-hand side
of the appliance.
•
• Push the machine back into the unit and fasten
the unit clamping lock.
•
•
Turn the steam knob (ref.1) anti-clockwise.
Press the hot water button (ref.5) and wait until
all the air in the boiler is released through the
steam spout (ref.16) and water starts coming
through.
ADJUSTING THE TEXTURE OF
GROUND COFFEE
•
The red indicator light (ref.9) illuminates at the
same time to indicate that the water in the
boiler is being heated. When the red indicator
• The machine is supplied already calibrated to
grind coffee beans to the ideal texture.
4
light goes out the water has reached the required
temperature for coffee making.
measure of ground coffee. For 2-cup filters
(ref.22) repeat the operation.
•
•
Close the steam knob by turnig clockwise (ref.1)
and release the hot water button (ref.5).
Allow any dispensed water to fall into the drip
tray or a cup and discard.
•
•
Press the ground coffee with the coffee press
(ref.17) .
Place the filter holder (ref.20) on the ring nut
(15) making sure it locks into place: move the
handle of the filter holder from left to right.
Place one or two coffee cups below the spout
of the filter holder with the correct nozzle
fitted.
•
ACCESSORIES SUPPLIED
•
•
When the red water temperature indicator light
(ref.9) goes out, press the coffee button (ref.4).
Once the required quantity of coffee has been
dispensed press the coffee button (ref.4) a
second time to stop the supply.
Remove cup(s) from the machine.
Remove the filter holder from the ring nut and
empty the used ground coffee from it.
•
•
The coffee machine is supplied with a filter
holder (ref.20) for one-cup filters (ref.21) and
two-cup filters (ref.22).
If you are using pods, use the one-cup filter.
A scoop (ref.23) is also supplied for measuring
ground coffee (approx. 7.2g).
•
•
OPTIONAL ACCESSORIES
MAKING COFFEE WITH PODS
(E.S.E. system)
•
A practical drawer with stainless steel front
panel is available as an optional accessory,
model ZDRA 600 X.
The drawer is divided into several compartments
for various uses :
compartment for cups and saucers
basin for coffee dregs
compartment for machine accessories (filter,
measure).
tray
•
E.S.E stands for Easy Serving Espresso and is
the International standard for making coffee
using pods (a pod is a disposable single-use
portion of roasted coffee) and a suitable coffee
machine. The E.S.E. system is simple, practical
and ecological since no special maintenance is
required and nature is respected. Lastly, the
system is clean as the special wrapping
prevents spillage and is easily removed and
disposed of after use.
-
-
-
-
The over all dimensions of the drawer are given
on page 18.
•
The machine is designed for use with ground
coffee or pods: single-use disposable portions
of roasted coffee.
MAKING COFFEE
•
•
Place the pod in the filter holder.
MAKING COFFEE WITH COFFEE
BEANS
Position the filter holder (ref.20) on the ring nut
(ref.15) making sure it locks into place: move
the handle of the filter holder from left to right.
Place a coffee cup below the spout of the filter
holder.
•
•
Only use fresh good quality beans.
•
•
Place the filter holder (ref.20) beneath the
dispenser (ref.19) and press the grinder button
for at least one second and release (ref.18) this
will automatically supply the correct one-cup
When the red water temperature indicator light
(ref.9) goes out, press the coffee button (ref.4).
5
•
Once the required quantity of coffee has been
supplied, press the coffee button a second time to
stop supply.
Remove cup(s) from the machine.
Take the filter holder off the ring nut and dispose
of the used pod.
•
•
Turn the steam knob (ref.1) anti-clockwise.
Press the hot water button (ref.5). Release the
button when you have the required amount of
hot water and close the steam knob (ref.1).
•
•
STEAM
TIPS ON HOW TO PREPARE AN
EXCELLENT ESPRESSO COFFEE
•
•
•
Steam is used to make cappuccino coffee (see
chapter "Recipes").
Keep the steam button (ref.6) pressed and wait
until the red indicator light (ref.9) goes out.
Place a receptacle beneath the steam spout and
slowly turn the steam knob (ref.1) anti-
clockwise.
•
To make good espresso coffee, the cleanliness of
the machine and the right temperature are
fundamental.
Make sure that the filter, the filter holder and the
ring nut are kept completely clean.
Unless you are away for long periods, keep the
machine turned on and the filter holder in the
ring nut to keep it hot.
Heat the coffee cups by filling them with hot
water (press the coffee button). This also
eliminates some of the water left in the boiler as
well as heats the filter holder.
When you have finished using the machine clean
the filter holder by running the machine without
coffee. This method eliminates any residues
which could alter the flavour of the coffee the
next time you use the machine.
•
•
•
•
When you have finished with the steam close
the steam knob by turning anti-clockwise
(ref.1) and press the steam button (ref.6).
If the steam comes into contact with a cool
surface on the surrounding furniture or outside
of the appliance, e.g. a trim, it will condense
and produce water droplets. This is quite
normal and not caused by a fault with the
machine. To prevent discolouration, regularly
wipe away condensation from surfaces.
•
•
•
For an excellent espresso, let the machine run for
20-25 seconds. The time required depends on the
texture of the ground coffee, the quantity of
coffee used and how firmly the coffee is pressed.
The machine is already calibrated to make good
quality coffee. If necessary the grinding texture
and the quantity of ground coffee dosed can be
adjusted (see paragraph "First Use") to obtain the
required strength and flavour.
RECIPES
ITALIAN CAPPUCCINO
This is a normal espresso coffee with steam-heated
milk that gives the coffee a milder flavour and a
rich, frothy topping. Serve in a large cup.
Pour cold milk into a tall jug and heat it using the
steam spout if your machine has one. Add only the
froth to the espresso coffee, to do this either tilt the
jug slightly rocking it backwards and forwards
while you pour or use a spoon to scoop off the
froth.
HOT WATER
You can also add a dusting of cocoa powder to
taste.
•
Place the coffee cup below the steam spout
(ref.16), using the handle to move the spout so as
not to cause burns.
6
VIENNESE CAPPUCCINO
CAPPUCCINO ICE-CREAM
This variation is the result of age-old Austrian
tradition.
Heat 2 cups of espresso coffee, ¾ cup of single
cream and ½ cup sugar in a pan and bring to
boiling point.
Leave to cool before placing in the freezer for 4-5
hours.
Move to the refrigerator ½ hour before serving.
Serve two-three balls of the ice-cream in a small
bowl and decorate with roasted coffee beans.
Prepare a 'long' espresso by letting the machine run
for longer than usual (30-35 seconds), add hot milk
followed by whipped cream. Serve in a medium-
sized cup (midway between an espresso cup and a
cappuccino cup).
Decorate with flakes of chocolate.
COLD ESPRESSO SHAKE
CLEANING AND
MAINTENANCE
Frothy and extremely refreshing, this makes a
pleasant drink on hot days.
Prepare an espresso coffee, add sugar and pour into
a cocktail shaker with large ice cubes. Shake for a
few seconds.
EXTERNAL PARTS
•
Clean all the external parts of the machine with
a soft cloth wrung out in warm water with a
little washing up liquid. Do not use harsh
detergents.
Do not clean steel surfaces with abrasive pads
or sponges or a high pressure washer.
Use a non-abrasive stainless steel cleaner for
more stubborn markes.
Serve in a tumbler or flûte.
IRISH COFFEE
•
•
•
Any energy-giving tonic.
Warm a tall glass and mix eight parts of hot coffee
with one part whisky and brown sugar.
Gently pour freshly whipped cream over the back of
a spoon so that it floats on the coffee: the result is a
layer of cool white cream on top of the hot dark
coffee.
Dry thoroughly using a soft cloth.
DRIP TRAY
•
•
Empty the drip tray (ref.25) regularly to avoid
the overflow of liquids which could soil and
damage the cupboards below the machine.
Both the drip tray and the grid are dish-washer
proof.
MEXICAN COFFEE
Intense and exotic.
Mix together a portion of double cream, half a
teaspoon of cinnamon, a pinch of nutmeg and sugar
in a small cup and beat until it becomes frothy.
Place a teaspoon of chocolate syrup, a pinch of
cinnamon and the coffee into a medium-sized cup
and blend together.
FILTER/FILTER-HOLDER/RING NUT
•
The filters (ref. 21 and 22), the filter holder
(ref.20) and the ring nut (ref.15) should be kept
clean at all times. Any residual coffee may alter
the taste of the next coffee you make.
Top with a teaspoon of vanilla-flavoured cream.
7
-
-
Pull down the glass retaining ring and glass.
Pull out the bulb and replace with one of the
same characteristics making sure that the glass
of the new bulb is not touched by hand.
Carefully wipe the new bulb with a soft cloth.
Refit the glass and glass retaining ring and
reconnect the machine to the electricity supply.
The bulb is a 20 watt, 12 volt halogen bulb
with a bi-pin fitting.
•
Put the filter holder and the filter in the
dishwasher every 2 months.
-
-
WATER TANK
•
•
If left unused for long periods it is advisable to
replace the water in the tank with fresh water and
to empty the boiler by pressing the coffee button
(ref.4) repeatedly.
Clean the water tank (ref.27) periodically to
remove any lime-scale.
SOMETHING NOT
WORKING
•
•
The water tank is dish-washer safe.
If Brita decalcifying filters are used it is
advisable to replace the filter every 2000
espresso coffees or at least every two months.
Ensure that the plastic tube is placed inside the
water tank so the water is fed into the machine.
Certain problems are due to lack of simple
maintenance or oversights, which can be solved
easily without calling out an engineer. Before
contacting your local Service Centre, please carry
out the checks listed below.
•
If the machine does not operate, check that:
− The machine is connected to the electricity
supply.
BOILER CLEANING FREQUENCY
•
Like any other appliance that uses water, it is
perfectly normal for lime-scale to form inside the
boiler of the coffee machine.
− The water tank is not empty.
-
-
-
It is advisable to clean the boiler every six
months as follows:
Fill the tank with 1.5l water and add half a glass
of vinegar or citric acid.
Press the coffee button repeatedly so that the
water/vinegar solution comes through a little at a
time until the tank is empty.
Repeat the operation until clean water comes
through (with no trace of lime-scale).
Fill the tank with cold water and again press the
coffee button repeatedly to rinse the boiler.
The machine is now ready for use.
If the power supply cable is damaged or for any
other maintenance operation please contact your
local Zanussi Service Centre.
TECHNICAL
ASSISTANCE AND
SPARE PARTS
-
-
-
If the problem persists after carrying out the check-
ups indicated in the previous chapter, contact your
nearest authorised Technical Assistance centre.
Always describe the fault and give the model
(Mod.), product number (Prod. no.) and serial
number (Ser. No.) of the appliance which are
indicated on the identification plate of the coffee
machine.
CHANGING THE LIGHT BULB
•
If the light bulb fails, ensure that the light
housing is cool before replacing the bulb. To
replace the bulb proceed as follows:
Disconnect the machine from the electricity
supply.
-
8
The plate is located on the external right-hand side
of the machine and is clearly visible when the
machine is opened.
* calls to this number may be recorded for training
purposes.
GUARANTEE
SERVICE AND SPARE PARTS (UK)
CONDITIONS (UK)
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Zanussi Service Force Centre by
telephoning:
ZANUSSI GUARANTEE CONDITIONS
We, Zanussi, undertake that if, within 24 months of
the date of the purchase, this Zanussi appliance or
any part thereof is proved to be defective by any
reason only of faulty workmanship or materials, we
will, at our option, repair or replace the same
FREE OF ANY CHARGE for labour, materials or
carriage on condition that:
* The appliance has been correctly installed and
used only on the gas and electricity supply stated
on the rating plate.
* The appliance has been used for normal domestic
purpose only, and in accordance with the
manufacturer's instructions.
* The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any
person not authorised by us.
* All service work under this guarantee must be
undertaken by a Zanussi Service Centre.
* Any appliance or defective part replaced shall
become the Company's property.
08705 929929
Your telephone call will be automatically routed to
the Service Force Centre covering your post code
area. The addresses are listed on the following
pages.
Before calling out an engineer, please ensure you
have read the details under the heading “FAULTS”.
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance.
5. The purchase date
CUSTOMER CARE DEPARTMENT
(UK)
* This guarantee is in addition to your statutory
and other legal rights.
For general enquiries concerning your Zanussi
appliance or for further information on Zanussi
products, please contact our Customer Care
Department by letter or telephone at the address
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside
these hours, in which case a premium will be
charged.
EXCLUSIONS
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
This guarantee does not cover:
* Damage or calls resulting from transportation,
improper use or neglect, the replacement of any
light bulbs or removable parts of glass or plastic.
* Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliance
outside the United Kingdom.
08705 727727 (*)
9
* Appliances found to be in use within a commercial
or similar environment, plus those which are the
subject to rental agreements.
* Products of Zanussi manufacture which are not
marketed by Zanussi.
When calling for repairs during the period of
guarantee ofthe appliance, the original invoice
or receipt must be shown or sent together with
the appliance to be repaired.
GENERAL CONDITIONS OF GUARANTEE
1 The manufacturer guarantees the appliance
indicated on the relative invoice for a period of one
year from the date of purchase. In case of a fault
during this period if caused bya defect in materials
and/or construction, the client is entitled to repair
free of charge.
EUROPEAN GUARANTEE
If you should move to another country within
Europe then your guarantee moves with you to your
new home subject to the following qualifications:
* The guarantee starts from the date you first
purchased your product.
* The guarantee is for the same period and to the
same extent for labour and parts as exist in the new
country of use for this brand or range of products.
* This guarantee relates to you and cannot be
transferred to another user.
* Your new home is within the European
Community (EC) or European Free Trade Area.
* The product is installed and used in accordance
with our instructions and is only used domestically,
i.e. a normal household
1a Concerning vacuum cleaners for domestic use,
the total periodof guarantee is two years.
Accessories are subject to a direct usage,
consequently these articles are excluded from the
guarantee.
2
The manufacturer guarantees technical
assistance and repairsfor one year. Spare parts
fitted during repair are also covered by a one year
guarantee from the date of repair. In case of fault
during this period, as a direct result of the repair
work carried out or caused by the new parts fitted
on such occasion, the client is entitled to repair free
of charge. The execution of repairs does not
prolong the total period of guarantee covering the
appliance.
* The product is installed taking into account
regulations in your new country.
Before you move, please contact your nearest
Customer Care centre, listed below, to give them
details of your new home. They will then ensure that
the local Service Organisation is aware of your
move and able to look after you and your appliances.
3 Technical Assistance At Domicile Will Be
Provided Only For Large Apparatus Which Are
Difficult To Transport Such As: Washing
Machines, Spin-Driers, Dishwashers,Refrigerators,
Freezers (Vertical Or Horizontal), Ovens, Cookers
And Built-In Appliances.
3a The above-mentioned conditions are also valid
for refrigerators for caravens on condition that they
are situated within the national boundaries and are
accessible by roads open to traffic. Furthermore, at
the time of the intervention the appliance and its
owner, or the person so authorized, must be present
at the place agreed upon for the intervention.
France
Germany
Italy
Sweden
UK
Senlis
+33 (0)3 44 62 29 99
+49 (0)911 323 2600
+39 (0)1678 47053
+46 (0)8 738 79 50
+44 (0)1753 219897
Nürnberg
Pordenone
Stockholm
Slough
GUARANTEE AND
SPARE PARTS (ONLY
FOR BENELUX)
4 If, in the opinion of the manufacturer, the
appliance as described in point 3 must be
transported to a Technical Assistance laboratory,
the transportation will be carried out as established
10
by the manufacturer, at his expense and under his
responsibility.
of the appliance, the manufacturer and the
technical assistance decline all responsibility.
8c Damage such as scratches, knocks or breakage
of movable or dismountable units which were not
notified to the manufacturer at the time of delivery
are not covered by the guarantee.
5 All appliances not mentioned under points 3 and
3a, includingappliances having the same functional
characteristics but whose transport is easy, must be
sent to the Technical Assistance or taken to them.
Throughout the period of guarantee the cost of
return transportation will be taken care by the
manufacturer.
6 If during the period of guarantee a disfunction
occurs due to a defect which cannot be repaired, the
appliance will be replaced free of charge.
IMPORTANT NOTICE
This appliance has been made to be safe.
Inadequate repairs can nonetheless compromise
this safety. To avoid such problems and to prevent
any eventual damage we advise you to have repairs
carried out exclusively by qualified personnel.We
advise you to have repairs or maintenance carried
out by the retailer or the ELECTROLUX
SERVICE and to request only original spare parts.
EXTENSION OF THE GUARANTEE
7 For motorcompressors of refrigerators/ freezers
(excluding the starting device and thermal
interrupter) a decreasing guarantee of 20% per year
for a period of five years from the date of purchase
of the appliance indicated on the relative invoice
with repairs free of charge throughout the entire
period under guarantee. On completion of the total
period of guarantee the cost of travel, workmanship
and eventual spare parts will be at the expense of the
client.
BELGIUM
Bergensesteenweg 719 / B - 1520 Halle
(Lembeek)
Repairing to customer's house:
Tel.: 02-3630444
Fax.: 02-3630400
Spare parts:
EXCLUSION FROM GUARANTEE
Tel.: 02-3630555
8 The free execution of work for the repair and/ or
substitution as set out above will not apply if:
- The purchase invoice or receipt indicating the date
of purchase and the identification of the appliance
cannot be presented or was not sent with the
appliance to be repaired;
Fax.: 02-3630500
LUXEMBOURG
7, Rue de Bitbourg / L-1273 Luxembourg-Hamm
Customer care:
Tel.: 42 43 11
Fax: 42 43 13 60
- The appliance is used for purposes other than those
of the domestic nature for which it was made;
- The appliance was not installed, handled or used in
conformity with the indications in the instruction
manual or in the modalities for use;
- The appliance has been repaired or modified
incorrectly by unqualified personnel.
8a If the appliance has been built-in, underinserted,
suspendedor installed in such a way that the time
required to move it and put it back in position
exceeds thirty minutes in total, the extra
expenditures occurred will be billed to the owner of
the appliance.
8b ln case of deterioration due to an irregular
installation carried out in agreement with the owner
11
TECHNICAL
SPECIFICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
Width
Depth
Height
Tank capacity
Net weight
594 mm
280 mm
357 mm
2,5 Iitres
17 kg
Gross weight
19 kg
Power supply voltage
Heater power consumption
Pump power consumption
230-240 V
1000 W
50 W
Light bulb power consumption 20 W
Total power consumption
Working pressure
Fuse
1070W
12 bar
13 A
INSTALLATION
INSTALLING IN MODULAR UNITS
This appliance must be installed by a competent
person.
For the appliance to work efficiently when installed
in a modular unit, the unit must have suitable
characteristics.
In conformity with safety standards, the appliance
must be installed correctly in order to guarantee
protection against contact between electrical parts
and parts with purely functional insulation.
All parts that act as guards, even the reveal side
panel for appliances installed at one extremity of a
combination, must be firmly secured so that they
cannot be removed without the use of tools.
It is advisable to avoid installing the appliance
immediately next to refrigerators or freezers since
the heat produced by the appliance could affect their
efficiency.
12
•
-
Warning:
Connect the power supply cable of suitable
dimensions before securing the power supply
unit.
Fig. 2
-
-
-
-
Assemble the runners on the sides of the
machine (using the screws supplied) as shown in
fig.1.
Fasten the telescopic runner supports (RH and
LH) using three wood screws (fig.2) and taking
care to follow the measurements shown in fig.2.
Make a slot in the bottom of the open
compartment following the measurements given
in fig.2.
If the compartment does not have a shelf for the
machine to rest on, assemble the machine fixing
bracket (ref.29) as shown in fig.4. Place screw 1
in the slot of the bracket and adjust the position
before locking in place using screw 2.
Fasten the power supply unit (fig.3) to the back
of the appliance in the top left-hand corner using
two wood screws as shown in fig.2.
-
Fig. 1
Fig. 3
Fig. 4
Fig. 5
•
Assemble the telescopic runners of the coffee
machine in the supports fixed to the inside of the
unit; push the runners in until they reach the
limit stop and secure the runners (fig.5).
14
WATER SUPPLY
•
Take the lid off the water tank (ref.27) and take
out the Brita filter.
•
Take the filter out of the packaging and soak it in
cold water for half an hour before fitting it firmly
into the hole in the tank (fig.6).
•
Place the water hose in the relative channel
(fig.7) and push it down until it reaches the
bottom of the tank (fig.8).
•
•
Fill the tank with cold water.
Warning: only fill the tank with cold drinking
water only: do not pour milk or any other liquid
into the tank!
•
The Brita filter is available at shops selling
household appliances, or your local Service
Centre.
Fig. 6
Fig. 7
Fig. 8
15
ELECTRICAL
CONNECTION
•
Make sure that the electric circuit is suitably
earthed.
•
Connect the power cable supplied to the
connector on the back of the appliance, plug the
connector into the power supply unit on the back
of the post (fig.3) where you will find the
terminal board (fig.9) set to operate at a supply
voltage of 230V monophase.
•
•
Make sure that a circuit breaker is installed in the
electrical circuit of the building to disconnect it
from mains and that contacts are at least 3mm
apart.
WARNING: the supplier disclaims all
responsibility in the case of non-observance of
the above rule.
Fig. 9
16
DRAWER
The required dimensions of the compartment for
installing the machine with the drawer are given in
fig. 10 and 11.
Fig.10
Fig.11
17
.
|